FAQs
- FAQs
- openEuler Fails to Start After It Is Installed to the Second Disk
- openEuler Enters Emergency Mode After It Is Started
- openEuler Fails to Be Reinstalled When an Unactivated Logical Volume Group Exists
- An Exception Occurs During the Selection of the Installation Source
- Kdump Service Fails to Be Enabled
- Fails to Selected Only One Disk for Reinstallation When openEuler Is Installed on a Logical Volume Consisting of Multiple Disks
- openEuler Fails to Be Installed on an x86 PM in UEFI Mode Due to Secure Boot Option Settings
- pmie_check Is Reported in the messages Log During openEuler Installation
- Installation Fails When a User Selects Two Disks with OS Installed and Customizes Partitioning
openEuler Fails to Start After It Is Installed to the Second Disk
Symptom
The OS is installed on the second disk sdb during the installation. The openEuler fails to be started.
Possible Causes
When openEuler is installed to the second disk, MBR and GRUB are installed to the second disk sdb by default. The following two situations may occur:
- openEuler installed on the first disk is loaded and started if it is complete.
- openEuler installed on the first disk fails to be started from hard disks if it is incomplete.
The preceding two situations occur because the first disk sda is booted by default to start openEuler in the BIOS window. If openEuler is not installed on the sda disk, system restart fails.
Solutions
This problem can be solved using either of the following two methods:
- During the installation of openEuler, select the first disk or both disks, and install the boot loader on the first disk sda.
- After installing openEuler, restart it by modifying the boot option in the BIOS window.
openEuler Enters Emergency Mode After It Is Started
Symptom
openEuler enters emergency mode after it is powered on.
Possible Causes
Damaged OS files result in disk mounting failure, or overpressured I/O results in disk mounting timeout (threshold: 90s).
An unexpected system power-off and low I/O performance of disks may also cause the problem.
Solutions
Log in to openEuler as the root user.
Check and restore files by using the file system check (fsck) tool, and restart openEuler.
NOTE:
The fsck tool checks and maintains inconsistent file systems. If the system is powered off or a disk is faulty, run the fsck command to check file systems. Run the fsck.ext3 -h and fsck.ext4 -h commands to view the usage method of the fsck tool.
If you want to disable the timeout mechanism of disk mounting, add x-systemd.device-timeout=0 to the etc/fstab file. For example:
#
# /etc/fstab
# Created by anaconda on Mon Sep 14 17:25:48 2015
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
/dev/mapper/openEuler-root / ext4 defaults,x-systemd.device-timeout=0 0 0
UUID=afcc811f-4b20-42fc-9d31-7307a8cfe0df /boot ext4 defaults,x-systemd.device-timeout=0 0 0
/dev/mapper/openEuler-home /home ext4 defaults 0 0
/dev/mapper/openEuler-swap swap swap defaults 0 0
openEuler Fails to Be Reinstalled When an Unactivated Logical Volume Group Exists
Symptom
After a disk fails, openEuler fails to be reinstalled because a logical volume group that cannot be activated existed in the system.
Possible Causes
During the installation of openEuler, a logical volume group cannot be activated.
Solutions
Before reinstalling openEuler, restore the abnormal logical volume group to the normal status or clear it. For example:
Restore the logical volume group.
Run the following command to clear the active status of the abnormal logical volume group to ensure that the error message "Can't open /dev/sdc exclusively mounted filesystem" is not displayed:
vgchange -a n testvg32947
Run the following command to recreate a physical volume based on the backup file:
pvcreate --uuid JT7zlL-K5G4-izjB-3i5L-e94f-7yuX-rhkLjL --restorefile /etc/lvm/backup/testvg32947 /dev/sdc
Run the following command to restore the logical volume group information:
vgcfgrestore testvg32947
Run the following command to reactivate the logical volume group:
vgchange -ay testvg32947
Run the following commands to clear the logical volume group:
vgchange -a n testvg32947 vgremove -y testvg32947
An Exception Occurs During the Selection of the Installation Source
Symptom
After the selection of the installation source, the message "Error checking software selection" is displayed.
Possible Causes
This is because the software package dependency in the installation source is abnormal.
Solutions
Check whether the installation source is abnormal. Use the new installation source.
Kdump Service Fails to Be Enabled
Symptom
The following information is displayed after running the systemctl status kdump command, indicating that no memory is reserved.
Possible Causes
The kdump service requires the system to reserve memory for running the kdump kernel. However, the system does not reserve memory for the kdump service. As a result, the kdump service cannot be started.
Solutions
For the scenario where the OS is installed
Add crashkernel=1024M,high to /boot/efi/EFI/openEuler/grub.cfg.
Restart the system for configuration to take effect.
Run the following command to check the kdump status:
systemctl status kdump
If the following information is displayed, the kdump status is active, indicating that the kdump service is enabled. No further action is required.
Parameter Description
The following table describes the parameters of the memory reserved for the kdump kernel.
Table 1 crashkernel parameters
Fails to Selected Only One Disk for Reinstallation When openEuler Is Installed on a Logical Volume Consisting of Multiple Disks
Symptom
If openEuler is installed on a logical volume consisting of multiple disks, an error message will be displayed as shown in Figure 1 when you attempt to select one of the disks for reinstallation.
Possible Causes
The previous logical volume contains multiple disks. If you select one of the disks for reinstallation, the logical volume will be damaged.
Solutions
The logical volume formed by multiple disks is equivalent to a volume group. Therefore, you only need to delete the corresponding volume group.
Press Ctrl+Alt+F2 to switch to the CLI and run the following command to find the volume group:
vgs
Run the following command to delete the volume group:
vgremove euleros
Run the following command to restart the installation program for the modification to take effect:
systemctl restart anaconda
NOTE:
You can also press Ctrl+Alt+F6 to return to the GUI and click Refresh in the lower right corner to make the storage configuration take effect.
openEuler Fails to Be Installed on an x86 PM in UEFI Mode Due to Secure Boot Option Settings
Symptom
During the installation of openEuler on an x86 PM in UEFI mode, the system stays at the "No bootable device" page and the installation cannot continue because secure boot is set to enabled (by default, it is set to disabled), as shown in Figure 2.
Figure 2 Dialog box showing "No bootable device"
Possible Causes
After secure boot is set to enabled, the mainboard verifies the boot program and OS. If the boot program and OS are not signed using the corresponding private key, they cannot pass the authentication of the built-in public key on the mainboard.
Solutions
Access the BIOS, set secure boot to disabled, and reinstall openEuler.
During the system startup, press F11 and enter the password Admin@9000 to access the BIOS.
Choose Administer Secure Boot.
Set Enforce Secure Boot to Disabled.
NOTE:
After Enforce Secure Boot is set to Disabled, save the settings, and exit. Then, reinstall the system.
pmie_check Is Reported in the messages Log During openEuler Installation
Symptom
PCP-related software package is installed if you select Server > Performance Tool during the OS installation. After the OS is installed and restarted, an error "pmie_check failed in /usr/share/pcp/lib/pmie" is reported in the /var/log/messages file.
Possible Causes
anaconda does not support the installation of SELinux policy module in the chroot environment. During the pcp-selinux installation, the postin script fails to execute the PCP-related SELinux policy module. As a result, an error is reported after the OS is restarted.
Solutions
After the OS is installed and restarted, perform either of the following two operations:
Install SElinux policy module pcpupstream.
/usr/libexec/pcp/bin/selinux-setup /var/lib/pcp/selinux install "pcpupstream"
Reinstall pcp-selinux
sudo dnf reinstall pcp-selinux
Installation Fails When a User Selects Two Disks with OS Installed and Customizes Partitioning
Symptom
During the OS installation, the OS is installed on two disks. In this case, if you select one disk for custom partitioning, and click Cancel to perform custom partitioning on the other disk, the installation fails.
Possible Causes
A user selects a disk for partitioning. After the user clicks Cancel and then selects the other disk, the disk information is incorrect. As a result, the installation fails.
Solutions
Select the target disk for custom partitioning. Do not frequently cancel the operation. If you have to cancel and select another disk, you are advised to reinstall the OS.
Learn More About the Issue at:
https://gitee.com/src-openeuler/anaconda/issues/I29P84?from=project-issue