Long-Term Supported Versions

    Innovation Versions

      Installation Mode

      NOTICE:

      • Only TaiShan 200 and FusionServer Pro servers are supported. For details about the supported server models, see Hardware Compatibility. Only a virtualization platform created by the virtualization components (openEuler as the host OS and QEMU and KVM provided in the release package) of openEuler and the x86 virtualization platform of Huawei public cloud are supported.
      • Currently, only installation modes such as CD-ROM, USB flash drive, network, QCOW2 image, and private image are supported. In addition, only the x86 virtualization platform of Huawei public cloud supports the private image installation mode.

      Installation Through a CD/DVD-ROM

      This section describes how to create or use a CD/DVD-ROM to install the openEuler.

      Preparing the Installation Source

      If you have obtained a CD/DVD-ROM, install the OS using the CD/DVD-ROM. If you have obtained an ISO file, record the ISO file to a DVD and install the OS using the obtained DVD.

      Starting the Installation

      Perform the following operations to start the installation:

      NOTE: Set the system to preferentially boot from the CD/DVD-ROM drive. Take the BIOS as an example. You need to move the CD/DVD-ROM Drive option under Boot Type Order to the top.

      1. Disconnect all drives that are not required, such as USB drives.
      2. Start your computer system.
      3. Insert the installation CD/DVD-ROM into the CD/DVD-ROM drive.
      4. Restart the computer system.

      After a short delay, a graphical wizard page is displayed, which contains different boot options. If you do not perform any operation within one minute, the installation starts automatically with the default options.

      Installation Through a USB Flash Drive

      This section describes how to create or use a USB flash drive to install the openEuler.

      Preparing the Installation Source

      Pay attention to the capacity of the USB flash drive. The USB flash drive must have sufficient space to store the entire image. It is recommended that the USB flash drive has more than 16 GB space.

      1. Connect the USB flash drive to the system and run the dmesg command to view related log. At the end of the log, you can view the information generated by the USB flash drive that is just connected. The information is similar to the following:

        [ 170.171135] sd 5:0:0:0: [sdb] Attached SCSI removable disk
        

        NOTE: Take the sdb USB flash drive as an example.

      2. Switch to user root. When running the su command, you need to enter the password.

        su - root
        
      3. Ensure that the USB flash drive is not mounted. Run the following command:

        findmnt /dev/sdb
        
        • If no command output is displayed, the file system is not mounted. Go to the next step.

        • If the following information is displayed, the USB flash drive is automatically mounted.

          $ findmnt /dev/sdb
          TARGET   SOURCE   FSTYPE  OPTIONS
          /mnt/iso /dev/sdb iso9660 ro,relatime
          

          In this case, you need to run the umount command to uninstall the device.

          umount /mnt/iso
          
      4. Run the dd command to write the ISO image to the USB flash drive.

        dd if=/path/to/image.iso of=/dev/device bs=blocksize
        

        Replace /path/to/image.iso with the complete path of the downloaded ISO image file, replace device with the device name provided by the dmesg command, and set a proper block size (for example, 512 KB) to replace blocksize to accelerate the write progress.

        For example, if the ISO image file name is /home/testuser/Downloads/openEuler-20.09-aarch64-dvd.iso and the detected device name is sdb, run the following command:

        dd if=/home/testuser/Downloads/openEuler-20.09-aarch64-dvd.iso of=/dev/sdb bs=512k
        
      5. After the image is written, remove the USB flash drive.

        No progress is displayed during the image write process. When the number sign (#) appears again, the write is complete. Exit the root account and remove the USB flash drive. In this case, you can use the USB flash drive as the installation source of the system.

      Starting the Installation

      Perform the following operations to start the installation:

      NOTE: Set the system to preferentially boot from the USB flash drive. Take the BIOS as an example. You need to move the USB option under Boot Type Order to the top.

      1. Disconnect all drives that are not required.
      2. Open your computer system.
      3. Insert the USB flash drive into the computer.
      4. Restart the computer system.

      After a short delay, a graphical wizard page is displayed, which contains different boot options. If you do not perform any operation within one minute, the installation program automatically starts the installation.

      Installation Through the Network Using PXE

      To boot with PXE, you need to properly configure the server and your computer's network interface to support PXE.

      If the target hardware is installed with a PXE-enabled NIC, we can configure it to boot the computer from network system files rather than local media (such as CD-ROMs) and execute the Anaconda installation program.

      For installation through the network using PXE, the client uses a PXE-enabled NIC to send a broadcast request for DHCP information and IP address to the network. The DHCP server provides the client with an IP address and other network information, such as the IP address or host name of the DNS and FTP server (which provides the files required for starting the installation program), and the location of the files on the server.

      NOTE: The TFTP, DHCP, and HTTP server configurations are not described here. For details, see Full-automatic Installation Guide.

      Installation Through a QCOW2 Image

      This section describes how to create or use a QCOW2 image to install the openEuler.

      Creating a QCOW2 Image

      1. Install the qemu-img software package.

        dnf install -y qemu-img
        
      2. Run the create command of the qemu-img tool to create an image file. The command format is as follows:

        qemu-img create -f <imgFormat> -o <fileOption> <fileName> <diskSize>
        

        The parameters are described as follows:

        • imgFormat: Image format. The value can be raw or qcow2.
        • fileOption: File option, which is used to set features of an image file, such as specifying a backend image file, compression, and encryption.
        • fileName: File name.
        • diskSize: Disk size, which specifies the size of a block disk. The unit can be K, M, G, or T, indicating KiB, MiB, GiB, or TiB.

        For example, to create an image file openEuler-image.qcow2 whose disk size is 32 GB and format is qcow2, the command and output are as follows:

        $ qemu-img create -f qcow2 openEuler-image.qcow2 32G
        Formatting 'openEuler-image.qcow2', fmt=qcow2 size=34359738368 cluster_size=65536 lazy_refcounts=off refcount_bits=16
        

      Starting the Installation

      Perform the following operations to start the installation:

      1. Prepare a QCOW2 image file.
      2. Prepare the VM network.
      3. Prepare the UEFI boot tool set EDK II.
      4. Prepare the VM XML configuration file.
      5. Create a VM.
      6. Start the VM.

      For details, see the openEuler 20.09 Virtualization User Guide.

      Installation Through a Private Image

      This section describes how to create or use a private image to install the openEuler.

      Creating a Private Image

      For instructions about how to create a private image, see Image Management Service User Guide.

      Starting the Installation

      For details about how to start the x86 virtualization platform of Huawei public cloud, see Elastic Cloud Server User Guide.

      Bug Catching

      Buggy Content

      Bug Description

      Submit As Issue

      It's a little complicated....

      I'd like to ask someone.

      PR

      Just a small problem.

      I can fix it online!

      Bug Type
      Specifications and Common Mistakes

      ● Misspellings or punctuation mistakes;

      ● Incorrect links, empty cells, or wrong formats;

      ● Chinese characters in English context;

      ● Minor inconsistencies between the UI and descriptions;

      ● Low writing fluency that does not affect understanding;

      ● Incorrect version numbers, including software package names and version numbers on the UI.

      Usability

      ● Incorrect or missing key steps;

      ● Missing prerequisites or precautions;

      ● Ambiguous figures, tables, or texts;

      ● Unclear logic, such as missing classifications, items, and steps.

      Correctness

      ● Technical principles, function descriptions, or specifications inconsistent with those of the software;

      ● Incorrect schematic or architecture diagrams;

      ● Incorrect commands or command parameters;

      ● Incorrect code;

      ● Commands inconsistent with the functions;

      ● Wrong screenshots.

      Risk Warnings

      ● Lack of risk warnings for operations that may damage the system or important data.

      Content Compliance

      ● Contents that may violate applicable laws and regulations or geo-cultural context-sensitive words and expressions;

      ● Copyright infringement.

      How satisfied are you with this document

      Not satisfied at all
      Very satisfied
      Submit
      Click to create an issue. An issue template will be automatically generated based on your feedback.
      Bug Catching
      编组 3备份